Straight Zipper vs U-Shaped Zipper Body Bags: Which Design Is Better?

If you put two closed body bags on a table, the difference between a straight zipper and a U-shaped zipper can look minor. I’d rather see both bags opened on the trolley your team actually uses. That’s where a wider opening can either make the job easier or leave a loose flap right where someone needs to stand.

4 min read
Side-by-side comparison of straight center and U-shaped body bag zippers

If you put two closed body bags on a table, the difference between a straight zipper and a U-shaped zipper can look minor. I’d rather see both bags opened on the trolley your team actually uses. That’s where a wider opening can either make the job easier or leave a loose flap right where someone needs to stand.

My rule of thumb: start with a straight center zipper if the middle opening gives you enough access. Look at a U-shaped zipper if you need more of the top panel to open and have room to fold it back. I wouldn’t choose either one from a catalogue photo alone.

Where I’d use a straight zipper

A center zipper opens the bag along one line. If your team works in a narrow aisle or regularly uses a compact trolley, it’s the first option I’d put on the trolley. Try the pull tab with gloves on, and make sure you can reach both ends without leaning across the trolley. I’d also check how far the opening spreads on its own. If someone has to hold both sides apart throughout the job, that center opening may not give your team enough room.

Where I’d choose a U-shaped zipper

I’d start here if the team needs a broader opening across the top. On many U-shaped designs, a larger part of the top panel folds back. The black zipper on this Jiekang white PVC body bag shows the path around three sides of the top panel. I pay attention to where the flap lands after it’s opened. Does it stay out of the way? Does it hang over the edge where someone needs to work? Then I run the slider through the corners. A generous opening loses some of its appeal if the zipper keeps catching at the turn.

The IFRC–ICRC body bag catalogue entry1 gives one example of a U-shaped zipper with two sliders. That’s one design, not a requirement for every bag. If the opening matters to your order, ask for a top-down photo of the exact sample, open and closed, before you decide.

What I’d check before placing a bulk order

  1. Use the same trolley for both samples. Choose bags of similar outside dimensions. For this equipment check, use empty bags or a clean training dummy.
  2. Measure the opening you can actually use. Note its length and width without having to pull the panels apart. If you’re still choosing the overall dimensions, start with our body bag sizing guide.
  3. Let the people who will use it try it with gloves. Have them open it partway, close it again and check where the pull tabs end up. If you need two sliders, write down where you want them to meet.
  4. Put the approved layout on the purchase order. Attach the sample photo or drawing. “U-shaped zipper” by itself leaves too much room for two people to picture different bags.
Two black zipper sliders with cord pulls on a white PVC body bag

One point I’d keep separate: opening access is not a leak test. If your purchase specification requires fluid containment or a stated working load, ask for evidence for the finished bag, including the closure, seams and relevant attachments. I wouldn’t give either zipper shape credit for performance it hasn’t been shown to deliver.

Is a U-shaped opening always wider?

Not in use. The path of the zipper, the width of the panel and the room available for the flap all matter. I’d measure the opening on the trolley rather than judge it from the outside dimensions.

Are two zipper pulls worth specifying?

Yes, if your team needs to open one section from a particular direction. If a single slider does the job on the sample, I wouldn’t add a second one just because it sounds better on the spec sheet.

Before I sign off on a bulk order, I want to see the sample open and close on the trolley it’s going to be used on. Then I’d put that exact zipper layout on the order.


  1. “Body bag”, IFRC and ICRC Standard Products Catalogue. The archived item listing provides an example of a U-shaped zipper with two sliders. ↩